PULLOUT STRENGTH

Pull Out Test Apparatus 500 kN (50 Tonne)

EKE 895:

This test is performed to measure the short- term strength of an installed Rockbolt under field conditions. The strength is measured by a pull test in which bolt head displacement is measured as a function of applied bolt load to give a load – displacement curve. This test is usually employed to assess the performance of the Rockbolt anchor resulting out of the quality of material used for manufacturer of Rock bolt and installation method used. The test equipment consists of a manually operated hydraulic pump connected to hydraulic jack, having a high strength test rod, coupled to the Rockbolt under test.

The anchor is tested measuring the load until a total displacement greater than 40 mm has been recorded or until the bolt yield or fractures , if this occurs first. The readings of displacement are taken in instruments of approx. 5 kN load or 5 mm displacement whichever occurs first. The rate of load application should be in the range 5-10 kN/min.. Readings are only taken after both load and displacement have stabilized . The time required for stabilization should be recorded

Consists of following : -

EKE 89001: Hydraulic Centre Hole Jack , 500 kN ( 50 Tonne) capacity with 54 mm Centre Hole, 150 mm Ram Travel, Double Acting

EKE 89005: Hand Operated , Two Stage Pump

EKE 89007: Thermoplastic Hose, 6 m long with pair of quick couplings.

EKE 89010: Load Gauge , 150 mm dia, 500 kN x 5 kN

EKE 89011: Reaction Frame , 500 kN capacity with 90 mm hole at base

EKE 89012: High Strength Test Rod, 40 mm dia.

EKE 89015: High Strength Coupling, having RH thread to suit Test Rod on one end LH thread to suit  32 mm dia. Rockbolt on the other end.

EKE 89016: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 25 mm dia. Rockbolt on the other end.

EKE 89017: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 30 mm dia. Rockbolt on the other end.

EKE 89018: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 32 mm dia. Rockbolt on the other end.

Dial Gauge , 0.01 x 25 mm

Pull Out Test Apparatus 250 kN (25 Tonne)

EKE 896:

This test is performed to measure the short- term strength of an installed Rockbolt under field conditions. The strength is measured by a pull test in which bolt head displacement is measured as a function of applied bolt load to give a load – displacement curve. This test is usually employed to assess the performance of the Rockbolt anchor resulting out of the quality of material used for manufacturer of Rock bolt and installation method used. The test equipment consists of a manually operated hydraulic pump connected to hydraulic jack, having a high strength test rod, coupled to the Rockbolt under test.

The anchor is tested measuring the load until a total displacement greater than 40 mm has been recorded or until the bolt yield or fractures , if this occurs first. The readings of displacement are taken in instruments of approx. 5 kN load or 5 mm displacement whichever occurs first. The rate of load application should be in the range 5-10 kN/min.. Readings are only taken after both load and displacement have stabilized . The time required for stabilization should be recorded

Consists of following : -

EKE 89001: Hydraulic Centre Hole Jack , 250 kN ( 25 Tonne) capacity with 54 mm Centre Hole, 150 mm Ram Travel, Double Acting

EKE 89005: Hand Operated , Two Stage Pump

EKE 89007: Thermoplastic Hose, 6 m long with pair of quick couplings.

EKE 89010: Load Gauge , 150 mm dia., 250 kN x 2.5 kN

EKE 89011: Reaction Frame , 250 kN capacity with 90 mm hole at base

EKE 89012: High Strength Test Rod, 40 mm dia.

EKE 89015: High Strength Coupling, having RH thread to suit Test Rod on one end LH thread to suit  32 mm dia. Rockbolt on the other end.

EKE 89016: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 25 mm dia. Rockbolt on the other end.

EKE 89017: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 30 mm dia. Rockbolt on the other end.

EKE 89018: High Strength Coupling having RH thread to suit Test Rod on one end and LH thread to suit 32 mm dia. Rockbolt on the other end.

Dial Gauge , 0.01 x 25 mm